Select Your Vehicle

Auto Carpet Installation - How To Install ACC Carpet in Trucks and Cars

Step-By-Step Auto Carpet Installation

How to Install Vinyl Flooring in a 1990 Dodge Ram

This video demonstrates how to install our ACC vinyl flooring in a 1990 Dodge Ram Truck. Whilst focused on a Dodge Ram vinyl flooring installation it will also give you some valuable pointers for how to install our carpets in any vehicle.

Focus Points –

  1. Where to start.
  2. How to cut our carpets to fit over gear shifters.

How To Install Auto Carpet in a 1993 GMC Truck

This video demonstrates how to install our ACC auto carpet replacement in a 1993 GMC Truck. Whilst focused on a GMC Truck carpet installation it will also give you some valuable pointers for how to install our auto carpets in any vehicle.

Focus Points –

  1. Where to start.
  2. How remove creases and wrinkles after removing the carpet from its packaging.

How To Install Auto Carpet in a 2001 Tahoe

This video demonstrates how to install our ACC auto carpet replacement in a 2001 Chevy Tahoe. Whilst focused on a Chevy Tahoe carpet installation it will also give you some valuable pointers for how to install our auto carpets in any vehicle.

Focus Points –

  1. Where to start.
  2. How to re-use the original trim rings with the new carpet.

How To Install Auto Carpet in a 1997 Camry

This video demonstrates how to install our ACC auto carpet replacement in 1997 Toyota Camry. Whilst focused on a Toyota Camry carpet installation it will also give you some valuable pointers for how to install our auto carpets in any vehicle.

Focus Points –

  1. Where to start.
  2. How to cut the carpet to account for larger center consoles.

How To Install Auto Carpet in a 2004 Town & Country Van

This video demonstrates how to install our ACC auto carpet replacement in 2004 Chevy Town & Country. Whilst focused on a Chevy Town & Country carpet installation it will also give you some valuable pointers for how to install our auto carpets in any vehicle.

Focus Points –

  1. Where to start
  2. How to mark and trim padding on carpets where padding is shipped loose.


Written Instructions

Flooring

READ FULL INSTRUCTIONS BEFORE BEGINNING
Instructions may vary for multi-piece sets

1. Remove new product from box. Lay flat and pop contours back into place. Allow a few hours for product to relax back into proper shape. Check material for accuracy.

2. Compare new and old carpet. (New product may have excess material on outer edges.)

3. In some applications it may be necessary to use old carpet as a template for console cuts.

4. IMPORTANT: Fold new product in half from front to rear. Place in vehicle lining up molded contour to seat risers or any other identifiable starting point on both driver and passenger sides. Once fitted, continue installation.

5. Roll product forward making any cuts needed for brackets, shifters and heater vents etc. while maintaining proper alignment on seat risers or other starting point.

6. Next, cut in center at firewall to allow product to go underneath dash.

7. Continue same procedure for remainder of installation – working your way to outer edges.

8. Once product is properly fitted you are now ready to do the final trimmings on outer edges, seat belts and holes etc.

Note: Applying adhesive to hold product in place is generally not necessary. If desired, only apply a light brush or spray adhesive after correct dry fit has been obtained.

Trunk Mats

READ FULL INSTRUCTIONS BEFORE BEGINNING
Instructions may vary for multi-piece sets

1. Verify piece count against the image shown on our website.

2. Compare new and old trunk mat.

3. Check material for accuracy.

4. Install kit according to image layout.

Note: Applying adhesive to hold product in place is generally not necessary. If desired, only apply a light brush or spray adhesive after correct dry fit has been obtained.

Sound Deadeners

READ FULL INSTRUCTIONS BEFORE BEGINNING
Instructions may vary for multi-piece sets

1. Verify piece count against the image shown on our website.

2. Check material for accuracy

3. Install kit according to image layout

Note: Some cuts or holes may be necessary depending on the application.

INSTALL USING THESE LISTED GUIDELINES
Instructions may vary for multi-piece sets
  • EVA – install poly side down / paper side up.
  • Mastic With Pad – install pad side down.
  • Foil With Pad – install pad side down.